New Furnace and Thermostat
A correctly sized gas or electric furnace from Carrier, Trane, Lennox, Goodman, Rheem, or York, plus a new programmable or smart thermostat. We register the manufacturer warranty in your name before we leave.
Licensed
Licensed & Bonded
Fully Insured
Insured & Bonded
24/7 Emergency
Same-Day Response
Warranty Backed
24+ Years Trusted
What Is Included in a Furnace Replacement
Every replacement we do includes the equipment, labor, permit, haul-away, and commissioning. Here is what you get when you hire us, and what would be a separate line item if your home needs it.
Permit and Inspection
We pull the local permit and schedule the inspection. You get a copy of both. Unpermitted furnace work can fail a home sale inspection years later, so we do it right the first time.
Flue and Gas Line Work
New flue connections, gas valve hookup, and combustion air intake as required by code. We test every connection with a manifold gauge set and leak detector before firing the unit.
Duct Sealing and Plenum
We seal the plenum and duct connections with mastic and duct sealant to stop the 20 to 30% of heated air that typically leaks out of old joints. This alone can cut your heating bill noticeably.
Old Equipment Haul-Away
We remove the old furnace, flue pipe, and any debris from the install. It goes on our truck and out of your basement. No dumpster rental, no extra fee.
Commissioning and Walkthrough
We verify temperature rise, check gas pressure, set the thermostat, and walk you through the filter location, shutoff valve, and warranty paperwork. We do not leave until the system holds temperature and you know how to run it.
Furnace Replacement in Ohio: What It Really Involves
Furnace Replacement in Ohio is the removal of your existing gas or electric furnace and the installation of a new, correctly sized heating system, including the flue, gas valve connections, thermostat, and duct interface. It is not a swap-and-go job. We run a combustion analyzer on the old unit to document why it failed, measure static pressure in the ductwork, and verify the new unit matches your home's actual heat load. Most installs take one full day, two if ductwork needs sealing or a plenum rebuild.
Ohio homes take a beating. Winters swing from 40 degrees to single digits in 48 hours, and furnaces in older housing stock from Chardon to Bellbrook run 5 to 6 months straight. When a heat exchanger cracks or a blower motor seizes in January, a repair bill of $900 on a 16-year-old unit rarely makes sense. That is when a furnace replacement service Ohio homeowners trust becomes the cheaper long-term call. We quote the swap out Ohio customers actually need, not the one that pads the invoice.
Our Furnace Replacement Process, Step by Step
No mystery, no surprise line items. Here is exactly what happens from the first phone call to the moment your new furnace fires up and holds temperature.
01
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
02
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
03
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
04
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Tools and Methods We Use on Every Install
Tools & Equipment
Manifold gauge set
Used to set and verify gas pressure on the new furnace. Correct inlet and manifold pressure is critical for safe, efficient combustion and is checked on every install.
Combustion analyzer
Measures carbon monoxide, oxygen, and flue temperature. We document readings before and after install so you have proof the system is burning clean.
Multimeter
Tests voltage, continuity, and resistance on igniters, flame sensors, blowers, and circuit boards during diagnosis and commissioning.
Inspection camera
Lets us look inside the heat exchanger and ductwork without tearing anything apart. Essential for confirming cracks and finding duct blockages.
Vacuum pump and flaring tool
Used on heat pump and AC coil work when the replacement includes a matched cooling system. Proper evacuation protects the compressor.
Duct cleaning equipment
We clean the ductwork before installing a new furnace so debris from the old system does not clog the new blower or secondary heat exchanger.
Methods & Standards
Manual J load calculation
We size the furnace based on square footage, insulation, window area, and climate zone, not by matching the old unit. An oversized furnace short cycles and wears out early. A correctly sized one runs longer, quieter, and more efficiently.
Static pressure testing
We measure pressure drop across the furnace and ductwork to confirm the blower can move the required airflow. High static pressure means the system is working too hard and will fail prematurely.
Code-compliant flue and combustion air
Every install meets current Ohio mechanical code for flue sizing, combustion air, and clearances. We pull the permit and pass the inspection so the work is documented and legal.
Duct sealing with mastic and duct sealant
We seal every joint we can reach with mastic and duct sealant. Leaky ducts waste 20 to 30% of the heat you pay for. Sealing is one of the cheapest efficiency upgrades you can make during a replacement.
When Ohio Homeowners Call Us for Replacement
01
Furnace is 18 years old and needs a $900 repair in December.
What we do: We quote both the repair and a replacement so you can compare. On an 18-year-old unit, replacement usually wins on total cost over the next five years. We can install within 48 hours.
→ You get a new furnace with a 10-year parts warranty instead of sinking money into a unit that will fail again next winter.
02
You are buying a house in Ohio and the inspection flags a cracked heat exchanger.
What we do: We provide a written replacement quote the seller and buyer can use in negotiation. We can also do the install after closing, often within a week.
→ You close with a known number instead of a surprise $6,000 bill in your first month of ownership.
03
Your gas bill jumped 40% and the furnace runs constantly but the house stays cold.
What we do: We check duct leakage, static pressure, and furnace output. If the unit is undersized or failing, we quote a correctly sized replacement with sealed ductwork.
→ A new 96% AFUE furnace plus duct sealing typically cuts heating costs 25 to 40% and holds temperature on the coldest nights.
04
You want to switch from an old electric furnace to gas or a heat pump.
What we do: We run a load calculation, check for a gas line or plan the electrical work, and quote both options with rebate eligibility spelled out.
→ You get a system that costs less to run, qualifies for available tax credits, and is sized for your actual home.
How Furnace Replacement Works Across Ohio
Ohio's climate is the reason furnace replacement matters here more than in milder states. From lake-effect snow belts near Geneva and Chardon to the colder river valleys around Belpre, heating season runs October through April and often longer. Homes built before 1980, which is most of the housing stock in towns like Martins Ferry, Wellston, and Uhrichsville, often have undersized ductwork and single-pane windows that put extra load on the furnace. We size replacements for the real house, not the sticker on the old unit. Ohio also requires permits and inspections on furnace replacements in most jurisdictions, and we pull them everywhere we work. If you have been searching for affordable furnace replacement Ohio homeowners can actually schedule, we run trucks across the state and can usually quote within 48 hours and install within a week.
Neighborhoods We Serve
-
Chardon and Geauga County
Lake-effect winters push furnace runtimes higher here. We size for colder design temperatures and recommend 96% AFUE units with sealed combustion for older farmhouse-style homes.
-
Bellbrook and Greene County
Mix of 1970s ranches and newer builds. We see a lot of original ductwork that needs sealing alongside the new furnace to hit efficiency targets.
-
Sunbury and Delaware County
Fast-growing new construction. We replace builder-grade furnaces that fail early and upgrade to properly sized two-stage or modulating units.
-
Belpre and the Ohio River Valley
Milder than the north but humid. We check for corrosion on flue pipes and recommend condensate management on high-efficiency units.
Local Conditions We Plan For
-
Single-digit cold snaps in January and February
Furnaces run continuously for days, exposing weak blowers, failing igniters, and undersized ductwork. We test for this during commissioning so the system holds up under real Ohio winter load.
-
Older housing stock with original ductwork
Ducts sized for a 1960s gravity furnace often cannot handle a modern high-efficiency blower. We measure static pressure and seal or resize ducts as part of the install.
-
Local permit and inspection requirements
Most Ohio jurisdictions require a permit and inspection on furnace replacement. We pull the permit, meet the inspector, and give you the sign-off paperwork for your records.
-
Natural gas availability varies by town
Some rural areas rely on propane or electric. We quote the right fuel type for your address and explain the operating cost difference before you commit.
1996 Furnace to 96% AFUE in Chardon
Furnace Problems We Solve With Replacement
Some furnace problems are worth fixing. Others mean the unit is on borrowed time. Here is how we tell the difference and when replacement is the right call.
Problem
Furnace blowing cold air in winter
A furnace blowing cold air usually means a failed igniter, a bad flame sensor, or a cracked heat exchanger. If it is the heat exchanger, you are looking at carbon monoxide risk and a repair that costs more than the unit is worth.
Our Fix
We diagnose the root cause with a multimeter and combustion analyzer. If the heat exchanger is cracked, we quote replacement on the spot. If it is a $180 igniter, we fix it and you keep the old furnace running.
Problem
Furnace short cycling every few minutes
Short cycling wears out the blower, igniter, and circuit board fast. It also means the furnace is oversized, under-ducted, or has a failing limit switch. Left alone, it kills the unit within a season or two.
Our Fix
We measure static pressure and check the limit switch. If the furnace is oversized, replacement with a correctly sized unit solves it permanently. If ductwork is the issue, we seal and resize what we can and quote the rest.
Problem
Furnace making loud noises on startup
Banging, rumbling, or screeching on startup points to a failing blower motor, a delayed ignition, or a dirty burner. Delayed ignition can crack the heat exchanger over time and is a safety issue.
Our Fix
We inspect the burners, clean or replace them, and test gas pressure. If the heat exchanger shows cracks, we stop there and quote replacement. We never patch a safety problem and send you back to bed.
Problem
Furnace leaking water around the base
A high-efficiency furnace produces condensate. A clogged drain line or cracked condensate pan leaks water onto your floor, which can rust the cabinet and damage the basement. Ignored, it leads to a no-heat call in the middle of a cold snap.
Our Fix
We clear the drain, inspect the pan and trap, and check the secondary heat exchanger. If the unit is old and the leak is internal, replacement is usually cheaper than chasing the problem every season.
Why Ohio Homeowners Replace Instead of Patch
A new furnace is not a luxury purchase. It is the difference between a $180 monthly gas bill and a $340 one, between a warm house and a cold one, and between a system that lasts 18 years and one that quits every February.
-
Lower Monthly Heating Bills
Modern 96% AFUE furnaces cut gas usage 25 to 40% compared to a 20-year-old 80% unit. On a typical Ohio winter bill of $260, that is $65 to $100 back in your pocket every month. The unit pays for a chunk of itself before the first spring.
-
Fewer Emergency Calls
A furnace that short cycles, trips the breaker, or blows cold air is telling you something. Replacing it before it dies means no 2 a.m. call, no space heaters, and no frozen pipes. We schedule installs within 48 hours of your quote.
-
Warranty and Parts Coverage
New Carrier, Trane, and Lennox units carry 10-year parts warranties from the manufacturer. That covers heat exchangers, circuit boards, igniters, and blowers. Old furnaces out of warranty mean every repair is out of your pocket, every time.
-
Safer Combustion, Cleaner Air
Cracked heat exchangers leak carbon monoxide into your living space. A new sealed-combustion furnace with a proper flue and fresh-air intake eliminates that risk. We test with a combustion analyzer before we leave and document the readings for you.
Licensed, Certified, and Accountable
Licensed & Certified
- NATE Certification — issued by North American Technician Excellence
- EPA Section 608 Certification — issued by U.S. Environmental Protection Agency
- OSHA Safety Certification — issued by Occupational Safety and Health Administration
- State HVAC License — issued by State of Ohio
- Local Permits and Inspection Sign-Off — issued by Local Ohio jurisdictions
Verified Reviews
Google ★★★★★4.9
Replaced our furnace in Chardon in one day. Techs were on time, pulled the permit, and cleaned up everything. New Trane runs quiet and the house heats evenly for the first time in years.
BBB ★★★★★4.8
Quoted us three options without pressure. We went with the mid-tier Lennox and could not be happier. Gas bill dropped about $70 a month. They came back to check the install a week later.
Yelp ★★★★★4.9
Emergency replacement in Sunbury on a Saturday. They had a new furnace in by evening and the house was warm. Fair price, no weekend surcharge games, and the workmanship warranty is real.
Google ★★★★★5.0
Did a load calculation instead of just matching our old unit. That alone set them apart from the other quotes. New Carrier system has been flawless through two Ohio winters.
Cities We Serve for Furnace Replacement in Ohio
We run furnace replacement service Ohio homeowners can schedule without the runaround. From the northeast snow belt to the southwest suburbs, our trucks cover the state and our techs know the local housing stock, permit rules, and climate quirks that affect every install.
Chardon
Lake-effect winters mean furnaces here work harder. We size replacements for colder design temps and recommend sealed-combustion 96% AFUE units for older Chardon homes.
Geneva
Geneva's mix of older homes and lake-effect cold calls for properly sized replacements with sealed ductwork. We pull the Ashtabula County permits and handle the inspection.
Belpre
Milder river-valley winters still demand a reliable furnace. We replace aging units in Belpre with correctly sized gas systems and check flue corrosion on every install.
Bellbrook
Bellbrook's mix of 1970s ranches and newer builds means ductwork varies block to block. We measure static pressure and seal ducts alongside every furnace replacement.
Sunbury
Fast-growing Sunbury has plenty of builder-grade furnaces hitting end of life early. We upgrade to two-stage or modulating units sized for the actual home, not the spec sheet.
What Ohio Homeowners Say
Real experiences from customers who chose our Furnace Replacement services.
“Our 1998 furnace died on a Friday in January. Emergency Furnace Repair had a tech out Saturday morning, quoted a Trane replacement, and installed it Monday. House was 68 degrees by 4 p.m. They pulled the permit and cleaned up everything. Could not ask for a smoother job.”
D
Dana R.
Homeowner, Chardon
“Got three quotes for furnace replacement. These guys were not the cheapest but they were the only ones who did a real load calculation instead of just matching the old unit's size. New Lennox runs quieter and our gas bill dropped about $80 a month. Worth every penny.”
M
Marcus T.
Homeowner, Bellbrook
“We had a cracked heat exchanger and did not know it until the inspection. They showed us the combustion analyzer readings and explained why replacement was the only safe option. Install was clean, they sealed the ductwork, and the new Carrier has been flawless through two winters.”
P
Priya S.
Homeowner, Sunbury
Furnace Replacement Questions Ohio Homeowners Ask
Real answers to the questions we hear most often from local homeowners and property managers.
How much does furnace replacement cost in Ohio?
Most Ohio furnace replacements run $3,200 to $7,800 installed, depending on unit size, efficiency rating, and whether ductwork needs work. A standard 80% AFUE single-stage unit in a 1,500 sq ft home typically lands around $3,800 to $4,500. High-efficiency 96% modulating systems with new flue and intake run $5,500 to $7,800. We give you a written quote before any work starts.
How long does furnace replacement take in Ohio?
A standard swap takes 6 to 9 hours, done in one day. If we need to rebuild a plenum, run a new flue liner, or fix ductwork, plan on a second day. We schedule most installs within 48 hours of quote approval and always confirm the start time the night before.
When should I replace my furnace in Ohio?
Replace when the unit is 15 to 20 years old, when repair costs exceed 40% of replacement, or when you see a cracked heat exchanger, repeated short cycling, or rising gas bills with no other explanation. If your furnace is over 18 and needs a $900 repair in December, replacement is usually the smarter money.
Are there tax credits for furnace replacement in Ohio?
Yes. High-efficiency gas furnaces meeting 97% AFUE or better can qualify for federal tax credits under current energy efficiency programs, and some Ohio utilities offer additional rebates. We provide the AHRI certificate and documentation you need to file. Ask us during the quote and we will tell you exactly what your chosen unit qualifies for.
Other Heating Services We Handle
Furnace Not Heating Repair
If your furnace runs but does not heat, we diagnose igniters, flame sensors, gas valves, and control boards. Sometimes a $200 repair saves the unit. When it does not, we quote replacement on the same visit so you are not paying twice for diagnostics.
View Furnace Not Heating RepairEmergency Furnace Repair
No heat at 2 a.m. in January is an emergency. We run 24/7 calls across Ohio and carry common parts on the truck. If the unit is beyond repair, we can often install a replacement within 48 hours.
View Emergency Furnace RepairFurnace Installation
New construction or first-time install. We handle load calculations, permit pull, gas line sizing, flue work, and commissioning. Same NATE-certified techs and same 1-year workmanship warranty as our replacement work.
View Furnace InstallationFurnace Maintenance
Annual maintenance keeps your new furnace under warranty and running at peak efficiency. We clean burners, check gas pressure, inspect the heat exchanger, and replace filters. Book it every fall before the first cold snap.
View Furnace MaintenanceFurnace Tune-Up
A tune-up is the once-a-year service call that catches small problems before they become no-heat calls. We test with a combustion analyzer, verify temperature rise, and tighten every electrical connection. Takes about 90 minutes.
View Furnace Tune-UpFurnace Inspection
Buying a house in Ohio? We inspect the furnace, heat exchanger, flue, and ductwork and give you a written report with photos. It tells you whether you are looking at a $200 fix or a $5,000 replacement before you close.
View Furnace InspectionContact Our Ohio Team
Call us any hour, any day. Our dispatchers answer live, give you a realistic arrival window, and route the closest truck to your address. If you prefer, send an email and we will reply the same business day with scheduling options.
Emergency Furnace Repair
-
Phone
+16149260837 -
Address
875 Freeway Dr N, Columbus, OH 43229
-
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available