Every electric furnace repair call includes a full diagnostic, a written estimate, the repair itself, and a post-repair test. We do not charge extra for the diagnostic if you approve the work. Here is what you get when you book with us.
We test voltage at the disconnect, check each heating element for continuity, verify the sequencer timing, and measure amp draw on the blower. This is not a visual inspection. It is a full electrical workup that finds the actual failure.
You get a written estimate before we start work. It lists the failed part, the replacement cost, and the labor. If the repair is not worth it, we tell you. No pressure, no upsell, no surprise charges on the invoice.
Most repairs are completed in a single visit. We stock heating elements, sequencers, blower motors, capacitors, and circuit boards for Carrier, Trane, Lennox, Goodman, and Rheem. If we do not have the part, we get it within 24 hours.
After the repair, we run a full cycle test. That means verifying temperature rise, checking amp draw on the blower, and confirming the furnace reaches setpoint without short cycling. We do not leave until it is running right.
Every repair comes with a 1-year workmanship warranty. If the same part fails within that year, we replace it free. We also honor manufacturer warranties on parts and file the paperwork for you.
Electric furnace repair in Ohio means diagnosing and fixing the heating elements, sequencers, blower motors, circuit boards, and capacitors that make an electric furnace run. Unlike gas systems, there is no flame to inspect, so the work centers on electrical continuity, voltage drop, and airflow. A technician uses a multimeter to test each heating element, checks the sequencer timing, and verifies the blower is moving the right CFM through your ductwork. Most repairs take two to four hours once we are on site.
Ohio winters push electric furnaces hard. When temperatures drop into the teens and stay there for days, a furnace that was limping along in November will fail in January. Homeowners in older housing stock, especially in towns like Wellston and Martins Ferry, often deal with undersized circuits, worn sequencers, and ductwork that has never been sealed. If your furnace is blowing cold air or short cycling, call before the problem takes out the blower too.
From your first call to the final test, here is exactly what happens when you book electric furnace repair with us. No mystery, no waiting around for a callback that never comes.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Multimeter
Tests voltage, continuity, and amp draw on heating elements, sequencers, and blower motors. This is the primary diagnostic tool for electric furnace repair.
Manifold gauge set
Used on heat pump systems paired with electric furnaces to check refrigerant pressures and verify the system is charged correctly.
Combustion analyzer
Used on gas furnace repairs to measure carbon monoxide levels and verify safe combustion. We also use it when converting from gas to electric.
Vacuum pump and refrigerant recovery machine
Used when repairing or replacing heat pump components that work alongside electric furnaces. We recover refrigerant to EPA standards before any work.
Inspection camera
Lets us see inside ductwork and behind panels without tearing anything apart. We use it to check for blockages, leaks, and heat exchanger cracks.
Duct cleaning equipment
When airflow problems are caused by dirty ducts, we clean them. Restricted airflow is a common cause of short cycling and high electric bills.
NATE-certified diagnostics
Every technician on our team holds NATE certification, which means they have passed third-party testing on electrical diagnostics, airflow, and system performance. We follow NATE protocols on every call.
EPA Section 608 compliance
When working on heat pump systems, we follow EPA Section 608 rules for refrigerant handling. We recover, recycle, and reclaim refrigerant properly. No venting, no shortcuts.
OSHA safety standards
Electrical work carries real risk. We follow OSHA safety standards on every job, including lockout/tagout procedures and proper PPE. Your home and our technicians stay safe.
Code-compliant repairs
We pull local permits when required and make sure every repair meets Ohio HVAC code. That matters when you sell your home or file an insurance claim. We do not cut corners.
01
What we do: We dispatch a technician immediately, 24/7. No overtime charges, no waiting until morning. We stock the most common parts so we can fix it on the first visit.
→ You get heat back the same night, usually within four hours of your call.
02
What we do: We diagnose the furnace and the ductwork. A failing sequencer or a blower that is not moving enough air will drive up your bill. We find the cause and fix it.
→ Your furnace runs less, your bill drops, and your home heats evenly again.
03
What we do: We perform a full furnace inspection, document the condition, and repair any issues the buyer's inspector found. We provide a written report with photos.
→ The sale moves forward without delays, and you have documentation for the buyer.
04
What we do: We give you an honest repair-versus-replace comparison. If repair makes sense, we fix it. If replacement is the better financial move, we walk you through the options.
→ You make a decision based on numbers, not pressure, and you stop throwing money at a failing furnace.
Ohio winters are hard on electric furnaces. Temperatures swing from the 40s to the teens in a matter of days, and that kind of cycling stresses heating elements and sequencers. In older housing stock, especially in towns like Wellston and Martins Ferry, we see undersized circuits, worn wiring, and ductwork that has never been sealed. In newer builds around Canfield and Columbiana, the issues are different: oversized furnaces that short cycle and ductwork that was not balanced. We adjust our approach based on what we find. If your furnace not heating is caused by a failing sequencer, we replace it. If it is a ductwork problem, we seal the leaks and verify airflow. We also pull local permits when required and make sure every repair meets Ohio code. One call covers it all.
Downtown Wellston
Older homes with original wiring and undersized circuits. We see a lot of failed sequencers and heating elements here.
Martins Ferry riverfront
Century homes with ductwork that has never been sealed. Airflow problems are common, and they cause short cycling.
Canfield Township
Newer construction with oversized furnaces. Short cycling and uneven heating are the typical complaints.
Columbiana historic district
Mix of older and newer homes. We adjust our diagnostic approach based on the age of the system and the ductwork.
Temperatures dropping into the teens for days
Electric furnaces run constantly, which wears out heating elements and sequencers. We see a spike in no-heat calls during cold snaps.
Older housing stock with original wiring
Undersized circuits and worn wiring cause voltage drop, which leads to premature element failure. We check the circuit on every call.
Ductwork that has never been sealed
Leaky ducts reduce airflow, which causes short cycling and uneven heating. We seal leaks and verify airflow before we leave.
Electric furnaces fail in predictable ways. Here are the most common problems we see across Ohio and how we fix them.
Problem
You wake up to a cold house and a furnace that runs but never warms up. The longer you run it, the more likely you are to burn out the blower too.
Our Fix
We test each heating element with a multimeter to find the failed one. In most cases, replacing the element or the sequencer restores heat the same day. We also check the limit switch and blower to make sure nothing else is about to fail.
Problem
Short cycling wears out the blower motor, the sequencer, and the limit switch. It also drives up your electric bill because the furnace never runs long enough to heat the house efficiently.
Our Fix
Short cycling is usually caused by a failing limit switch, a clogged filter, or a blower that is not moving enough air. We diagnose the root cause, replace the failed part, and verify proper airflow through the ductwork.
Problem
Banging, screeching, or humming from an electric furnace usually means a blower motor bearing is failing or a sequencer is arcing. Ignoring it can lead to a complete blower failure.
Our Fix
We inspect the blower motor, check the bearings, and test the sequencer. If the motor is failing, we replace it. If the sequencer is arcing, we swap it out. Most noise issues are resolved in one visit.
Problem
A furnace that will not turn on is usually a tripped breaker, a blown fuse, or a failed circuit board. In cold weather, this becomes an emergency within hours.
Our Fix
We check the breaker, test the control board, and verify voltage at the disconnect. If the board is dead, we replace it. If it is a simple fuse or breaker issue, we fix it and show you what caused it.
We have been repairing electric furnaces across Ohio since 2002. That is 24 years of diagnosing the same failures in the same housing stock, and it means we usually know what is wrong before we pull into your driveway.
Same-day heat restored
Most electric furnace repairs are finished in a single visit. We carry heating elements, sequencers, blower motors, and circuit boards for Carrier, Trane, Lennox, Goodman, and Rheem on every truck. If your furnace is not turning on, we can often have you warm again within four hours of your call.
Upfront pricing, no surprises
You get a flat repair price before we start work. Diagnostic runs $89 and is waived if you approve the repair. Typical electric furnace repairs in Ohio run $180 to $650 depending on the part, and we tell you the number before we open a panel. No hourly billing, no parts markup games.
NATE-certified technicians
Every technician on our team holds NATE certification and EPA Section 608 certification. That means they have passed third-party testing on electrical diagnostics, airflow, and refrigerant handling. We also carry OSHA safety certification and pull local permits when the job requires it.
24/7 emergency response
Electric furnaces do not fail at convenient times. We answer the phone at 2 a.m. on a 10-degree night and dispatch a technician. Emergency furnace repair is the same price as a scheduled call, and we do not charge overtime on weekends or holidays. Call +1 614-926-0837 any hour.
Google ★★★★★4.9
Called at 9 p.m. on a Friday. Technician arrived by 10:30. Diagnosed a bad sequencer, had the part on his truck, and fixed it by midnight. Price was exactly what he quoted. No overtime charge. These guys are the real deal.
Yelp ★★★★★4.8
Two other companies told us we needed a new furnace. These guys found a loose connection and a failing capacitor. $240 total. That was three years ago and it is still running. Honest and skilled.
BBB A+
Professional from start to finish. The technician explained what was wrong, showed me the failed part, and gave me a written estimate before starting work. Clean, courteous, and fair. Highly recommend.
We have been fixing electric furnaces across Ohio since 2002. In that time, we have worked on every major brand, from Carrier and Trane to Goodman and Rheem, and we have seen the same failures repeat in the same neighborhoods. Our technicians hold NATE certification, EPA Section 608 certification, and OSHA safety certification, and we keep up with Ohio HVAC licensing requirements and local permit rules. When we diagnose your furnace, we are not guessing. We are recognizing a pattern we have fixed hundreds of times.
We deliver electric furnace repair in Ohio from the Ohio River to the Lake Erie shore. Our technicians cover Wellston, Martins Ferry, Columbiana, Canfield, and dozens of towns in between. Whether you are in a century home or a newer build, we know the local housing stock and the failures that come with it. One call, one dispatch, and a technician who knows your neighborhood.
Older homes with original wiring and undersized circuits. We see a lot of failed sequencers and heating elements here. Same-day service available.
Century homes with ductwork that has never been sealed. Airflow problems are common, and they cause short cycling. We diagnose and fix both.
Mix of older and newer homes. We adjust our diagnostic approach based on the age of the system and the ductwork. Same-day repair available.
Newer construction with oversized furnaces. Short cycling and uneven heating are the typical complaints. We size the repair to the system.
Real experiences from customers who chose our Electric furnace repair services.
“Our electric furnace quit on a Friday night in January. I called at 9 p.m. and a technician was here by 10:30. He tested the elements with a multimeter, found a bad sequencer, and had the part on his truck. We had heat by midnight. The price was exactly what he quoted. No overtime charge.”
Dana R.
Homeowner, Wellston
“We had been dealing with a furnace that short cycled for two winters. Two other companies told us we needed a new furnace. These guys found a loose connection on the blower and a failing capacitor. $240 total. That was three years ago and it is still running. They saved us thousands.”
Marcus T.
Homeowner, Martins Ferry
“I called about my furnace blowing cold air. The technician arrived within two hours, diagnosed a failed heating element, and replaced it the same visit. He also showed me the old part and explained why it failed. Clean, professional, and the price was fair. I will use them again.”
Karen L.
Homeowner, Canfield
Real answers to the questions we hear most often from local homeowners and property managers.
When your furnace runs but does not heat, the problem is usually a failed heating element, sequencer, or limit switch. We diagnose the exact cause and repair it the same day. This is the most common electric furnace repair we handle in Ohio.
View Furnace Not Heating RepairNo heat at 2 a.m. on a 10-degree night is an emergency. We dispatch a technician immediately, 24/7, with no overtime charges. Same pricing as a scheduled call, and we stock the parts needed to get you warm fast.
View Emergency Furnace RepairIf your electric furnace is beyond repair, we install new Carrier, Trane, Lennox, Goodman, and Rheem systems. We handle sizing, permits, and code compliance. Most installations are completed in one day, and we haul away the old unit.
View Furnace InstallationWhen repair costs approach half the price of a new furnace, replacement makes more sense. We walk you through the numbers, help you pick the right size and efficiency, and install it within a week. Financing is available on approved credit.
View Furnace ReplacementAnnual maintenance keeps your electric furnace running through Ohio winters. We test heating elements, tighten electrical connections, clean the blower, and replace filters. A $129 tune-up in the fall prevents most mid-winter breakdowns.
View Furnace MaintenanceA furnace tune-up is a 60-minute service that includes a full electrical inspection, amp draw test on the blower, and temperature rise check. We also replace your filter and clean the blower compartment. Book in September before the rush.
View Furnace Tune-UpCall us any hour, any day. Our dispatchers answer live, give you a realistic arrival window, and route the closest truck to your address. If you prefer, send an email and we will reply the same business day with scheduling options.
Phone
+16149260837Address
875 Freeway Dr N, Columbus, OH 43229
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
